Injection guide · Ferring Pharmaceuticals

How to mix and inject MENOPUR

This guide takes you through mixing and injecting MENOPUR with the Q•Cap, one step at a time. It covers 6 stages, from washing your hands to disposing of your needle. Set the number of vials your clinic prescribed, and the guide repeats the vial steps for each one.

Loading introduction video…

What the guide covers

  1. 1Getting ready4 steps
    1. Wash your hands and gather supplies

      Wash your hands with soap and water, dry them with a clean towel, and place all supplies on a clean surface.

    2. Inspect each MENOPUR vial

      Look closely for MENOPUR powder or a small pellet inside each vial.

    3. Inspect the saline and Q•Cap package

      Check that the Sodium Chloride vial contains clear liquid without visible particles and that the Q•Cap blister package is intact.

    4. Remove caps, clean vial tops, and open the Q•Cap package

      Remove the plastic caps from the MENOPUR and Sodium Chloride vials. Wipe the vial tops with an alcohol pad and let them dry. Peel open the Q•Cap blister package.

      Do not touch the spike or connector ends of the Q•Cap.

  2. 2Mixing your medication3 steps repeat for each of your 1 vial9 steps
    1. Attach the Q•Cap to the Sodium Chloride vial

      Hold the sides of the Q•Cap blister, turn it over onto the Sodium Chloride vial, and push straight down until the spike pierces the stopper and the Q•Cap snaps into place.

      Do not touch the connector end of the Q•Cap.

    2. Draw air into the syringe

      Pull the syringe plunger rod down to the line that matches the amount of Sodium Chloride your healthcare provider told you to use.

      Be careful not to touch the syringe plunger during this step.

    3. Connect the syringe to the Q•Cap

      Place the syringe tip into the Q•Cap connector and twist the syringe clockwise until secure.

      Do not overtighten.

    4. Push the air into the Sodium Chloride vial

      Slowly press the plunger to push the air from the syringe into the vial.

    5. Withdraw the prescribed amount of Sodium Chloride

      Keeping the syringe and Q•Cap together, turn the vial upside down and pull the plunger down to withdraw the amount of Sodium Chloride your healthcare provider specified.

    6. Remove the Sodium Chloride vial

      Pull up on the syringe barrel to separate the syringe and Q•Cap from the Sodium Chloride vial, then discard the Sodium Chloride vial.

      Be careful not to remove the Q•Cap from the syringe.

    7. Attach the Q•Cap to a MENOPUR vial · for each vial

      Hold the MENOPUR vial and press the Q•Cap into the vial's rubber stopper until it stops and snaps into place.

      Do not press the syringe plunger while attaching the Q•Cap to the vial.

    8. Add the Sodium Chloride and dissolve MENOPUR · for each vial

      Slowly push the Sodium Chloride into the MENOPUR vial, then gently swirl until the powder is completely dissolved.

      Do not shake the vial; Ferring states that shaking can cause air bubbles.

    9. Withdraw all of the mixed MENOPUR · for each vial

      Once the powder is fully dissolved, press the plunger down to empty remaining air from the syringe, turn the vial upside down, and pull the plunger down to withdraw all of the MENOPUR.

      Do not pull the plunger stopper completely out of the syringe barrel.

  3. 3Ready to inject2 steps
    1. Remove the syringe from the Q•Cap

      After the final vial is mixed and all medicine is in the syringe, hold the Q•Cap steady and twist the syringe counterclockwise to remove it.

    2. Discard the Q•Cap and attach the injection needle

      Discard the Q•Cap with its attached vial. Hold the syringe tip upward, place the needle on the syringe, and twist it clockwise until secure.

      Keep the needle cap on until you are ready to inject.

  4. 4The injection4 steps
    1. Choose and clean the injection site

      Choose a site on the abdomen 1–2 inches below the navel, clean it with an alcohol pad, and let it air-dry.

    2. Remove the needle cap and clear air from the syringe

      Remove the needle cap, point the needle straight up, pull the plunger down slightly, and tap the syringe barrel so air bubbles rise. Slowly press the plunger until the air is out and a small drop appears at the needle tip.

      Do not let the needle touch anything so it remains sterile.

    3. Pinch the skin and insert the needle

      Gently pinch a fold of skin between your thumb and index finger. Hold the syringe at a 90-degree angle and quickly insert the needle all the way into the skin fold.

    4. Inject the medication and remove the needle

      Press the plunger with a steady motion until all of the fluid has been injected, then release the skin fold and pull the needle straight out.

  5. 5Right after2 steps
    1. If the injection site is bleeding

      Only if it applies.

      If there is bleeding, place a gauze pad over the site and apply gentle pressure until the bleeding stops.

      Do not rub the injection site.

    2. If the site becomes sore or red

      Only if it applies.

      If needed, place ice on the injection site for 1 minute, remove it for 3 minutes, and repeat.

  6. 6Tidying up2 steps
    1. Dispose of used needles and syringes

      Put used needles and syringes into an FDA-cleared sharps disposal container immediately after use.

      Do not put loose needles or syringes in household trash.

    2. Discard the remaining debris

      Discard the remaining used packaging and other non-sharp debris in household trash.